PLUMBING BASICS: THE FIRST STEP FOR BATHTUB INSTALLATION

Plumbing Basics: The First Step for Bathtub Installation

Plumbing Basics: The First Step for Bathtub Installation

Blog Article

Click Here

Were you hunting for guidance around Installing A Bathtub?


A Step-by-Step Guide to Installing a Bathtub
Installing a tub isn't precisely rocket science, yet it does require solid plumbing, carpentry, and often, tiling skills. Replacing an old tub with a new one is additionally a reasonably hard job. If the old tub is readily accessible, the job can move speedily; if you have to open up a wall surface to get rid of the old tub as well as position the brand-new tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. See to it you have qualified on your own for the task and also are comfortable attempting it. Instead of working with a specialist to take control of a halfway-completed task, it is better to think about employing one before you begin. Chances are you may need a professional plumber to make tube links.
This short article will certainly aid you set up a brand-new bath tub in your bathroom if you have currently bought a brand-new tub and do not require to transform the setup of your previous water pipelines.
Your tools and product checklist must comprise the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, activate the taps to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited access that is commonly the case.
    Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
    Before proceeding to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end provides a connection to the current supply pipes.
    If you require to fit a monobloc, then you will require reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Secure the tap in position with the producer supplied backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind should be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

    Setting up the Bathtub


    Utilizing both wood boards under its feet, place the bathtub in the called for position. The wood boards are valuable in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little points.
    The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the tub until the spirit level reads degree.
    To mount faucets, fit the bottom of the furthest versatile faucet port to the suitable supply pipeline by making a compression join; after that do the same for the various other faucet.
    Switch on the water supply as well as check all joints and new pipework for leaks as well as tighten them if required. Fill up the bath tub and additionally check the overflow electrical outlet as well as the typical electrical outlet for leaks.
    Lastly, deal with the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the tub ought to wait till the tub has been made use of at the very least when as this will certainly settle it right into its final setting.

    Getting ready for the Setup


    First of all, the supporting structure provided with the bath must be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
    Fit the adaptable tap adapters to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split an inflexible seal, creating the water to permeate the wall surface in between the bathroom and the tiling, causing complications with dampness and possible leaks to the ceiling listed below.
    You can select from a variety of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water before securing, to enable the activity experienced when the tub remains in use. The sealant can break fairly early if you do not take into consideration this motion prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the floor tiles utilizing water-resistant or water-proof glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    As a serious reader about How to Install a Bathtub Yourself, I think sharing that piece of content was really useful. So long as you appreciated our blog posting please don't forget to pass it around. We enjoy reading our article about How to Install a Bathtub Yourself.


    Connect for quality.

    Report this page